Jackson Panic Device
Jackson has been around for 50 years and has always specialized in concealed door closers for storefront doors. The earliest model of Jackson panic devices was the 885, which was a concealed vertical rod, narrow stile panic device. It has been replaced by the Jackson 1085 which came out in the mid 1970s.
At RBADoor.com, we provide an online platform where consumers can order Jackson panic devices and parts. We carry several series of Jackson exit devices such as the Jackson panic device model 1085 and the Jackson 2095 Series.
We also offer the option of purchasing Jackson panic hardware for when you have to repair the Jackson panic devices that have already been installed on a commercial door. With numerous products to choose from, you can’t go wrong when ordering Jackson panic devices from RBADoor.com.
Shipping Jackson Panic Devices
Most of the Jackson panic devices that we carry on our online store will ship within 24 to 48 hours of an order placement. Special sizes, finishes and some Jackson panic device parts are factory orders that may take up to 3 weeks. All In Stock Jackson replacement parts ship out within 24 hours.
Jackson Panic Devices Models
Jackson 885 Series – The Jackson 885 was introduced in the 1960’s for use in aluminum framed glass storefront doors. It was discontinued in the 1970’s, but we still run into the Jackson 885 Series today. There is not an exact replacement for this Jackson panic device, and it is usually less expensive to replace the door and frame instead of trying to retrofit newer Jackson panic devices in its place.
Jackson 1085 Series – Introduced in the 1970’s, the Jackson exit device model 1085 is a concealed vertical rod, cross bar style device. The Jackson exit device model 1085 usually ships in about 24 hours and we stock all of the replacement hardware. We ship the Jackson exit device model 1085 with a 4 foot cross bar that is easily trimmed to size in the field.
The Jackson exit device model 1085 is non-handed and comes in three finishes. Call or email for a breakdown of parts for Jackson exit device model 1085.
Jackson 1095 Series – The 1095 Series Jackson panic devices were also introduced in the 1970’s. These Jackson panic devices are a cross bar style, rim device, meaning they have a latch bolt that sticks out of the active housing and latches on the rim of the doorframe.
We also ship 1095 Series Jackson exit devices with a 4 foot cross bar that is easily trimmed to size. These Jackson exit devices also ship in 24 hours, are handed and come in three finishes. Call or email us for a breakdown of parts.
Jackson 1285 Series – The Jackson exit device 1285 is a concealed vertical rod device for narrow stile doors. The 1285 series uses the same concealed rods as the 1085 Jackson exit device above, but is a touch bar style device. If you have a 1085 and would like to convert it to a touch bar style device, then the Jackson exit device 1285 would be the exit device to use. The Kawneer 1686 is the same device as the 1285.
Jackson 1295 Series – The 1295 is the rim equivalent of the Jackson 1285 series. It is designed for narrow stile single storefront doors. This Jackson panic device ships in 24 to 48 hours and we offer it in two finishes. We require the door width and handing to order these Jackson exit devices. The Kawneer 1786 is the same device as the Kawneer 1786.
Jackson 2085 Series – The Jackson 2085 is a concealed vertical rod device that has been around since the 1980’s. This device is more heavy duty than the ones above, but it is not as common. We would need to know the color, right or left hand, and door width when ordering these Jackson exit devices.
Jackson 2095 Series – The Jackson 2095 is a rim exit device and has the exact appearance as the Jackson 2085. When you order these Jackson panic devices, please choose the color, door width, and whether it will be used with a right or left handed door.
History of Jackson Panic Devices
For over 50 years Jackson has been manufacturing high-quality hardware for the aluminum and tempered glass industry. Their overhead concealed 20-330 door closer, 885, 1085 and 1095 Jackson panic devices, and pivots were industry leaders when they were introduced in the late 1960’s.
Today, the Jackson exit devices company is owned by C.R. Laurence Company, Inc. (CRL). CRL Jackson exit devices and parts are manufactured in the CRL manufacturing plant in LA.
Our site, RBADoor.com, offers an easy-to-navigate platform for purchasing CRL Jackson exit devices online. Keep us as your designated online distributor of CRL Jackson exit devices for the next time you need to order them. This way, you can save our page in your Bookmarks, hop on our site, key in your search, and be on your way to ordering your CRL Jackson exit devices in no time.
Ordering Jackson Exit Devices
Ask us any questions, whether it’s about the Jackson 2085 Series, the Jackson exit device 1285 or any other Jackson exit devices and replacement hardware. Get ahold of us by phone or email on weekdays from 8 a.m. to 5 p.m. Eastern Time and we will be available to assist you with your order of Jackson exit devices. We are looking forward to helping you out with your next Jackson exit devices order.
-
Jackson 1085 Panic Device Concealed Vertical Rod
The Jackson 1085 Panic Device is one of a few original manufactures of Panic Hardware for aluminum framed glass doors, or storefront doors. The 1085, 1095 along with their door closer the 20-330 were installed on about half of these doors in the 1970's and 1980's. They were installed on Vistawall and Kawneer doors just to name a few. Universally recognized as the standard for aluminum storefront hardware it is made of high tensile strength aluminum. The device is Non Handed, Comes with 45" cross bar that is easily cut in the field. Also includes the Concealed Vertical Rods, Screws and Strikes.
Replacement parts are available, in stock!
1085EO -
Jackson 1095 Panic Rim Device
The Jackson 1095 Panic Hardware was one of the first devices universally recognized as the standard for aluminum storefront hardware. Made of high tensile strength aluminum. It ships complete with both housings, crossbar, all the fasteners, and the strike. Comes with 45" cross bar that is easily cut in the field.
1095EO -
Jackson 1095P Paddle Panic Hardware
The Jackson 1095P Paddle Panic Hardware is an alternative to the cross bar or push pad style panic hardware. The device is the same as the Jackson 1095, but with a paddle instead of the cross bar. This device is for use on aluminum or steel doors only. The device is mounted on surface studs that are tapped into the door. On a wood door they will pull out.
Right Hand Reverse Shown
1095P- -
Jackson Panic Device Top Bolt Guide Assembly 1085/1285/2086
The Jackson Panic Device Top Bolt Guide Assembly is used on the 1085, 1285, and 2086 hardware. The piece works by sliding over the top rod when the device is opened. This keeps the rods retracted until the Plunger hits the Trip Assembly when it is closing. Upon hitting the Trip Assy, the plate slides over and the rods retract. It measures 1-1/2” deep x 1-1/16” wide x 15/16” tall, with a hole spacing of 3/4" on the mounting screws. Assembly includes the mounting screws. The Jackson Part number is 30-934.
G108518 -
Jackson Panic Device 1085 And 1095 Dogging Pin
The Jackson Panic Device 1085 And 1095 Dogging Pin is the piece that keeps the hardware in the open position during business hours. It is activated by pressing the crossbar and then turning the flat head screw driver head. The pin is held in the housings with a screw, which is located on the back of the housing. This pin has been used since about 1988 or so, the old style are no longer made, but they had a roll pin that was used to hold it in place. This package comes with a new spring, set screw and the pin. The Jackson part number on this is 30-1115.
G108554 -
Jackson Panic Device Mounting Stud 1085/1095
The Jackson Panic Device Mounting Stud is for use on the 1085 and 1095 panic hardware. Each door would have 2 on the left and 2 on the right, so a total of 4 studs per door. The housings fit over these studs and are held in place by an 1/8" set screw, there are two of these set screws at the top and one on the bottom. The threaded part has a 1/4-20 thread.G108544 -
Jackson Panic Device Crossbar 1085/1095
The Jackson Panic Device Crossbar is for use on the 1085 and 1095 hardware. The bar is 45" long and can be cut in the field with a chop saw or hack saw. There is a groove the entire length of the bar for added and strength and for the thread forming screws to thread into. The Jackson part number is 30-733-PKG, and it ships with the cross bar screws.
Jackson Part # 30-744PKG or 30744PKG
G108520- -
Jackson Panic Device Center Case 1085/1095
The Jackson Panic Device Center Case 1085/1095 is for use with the 1085 devices for both and left, and the inactive case of the 1095. Case is easily removed by loosening the two 1/8" Allen screws and one on the bottom. Includes everything in the housing. The distance between the mounting studs on this Case is 6-5/16"
Jackson part # 30-982 Right Hand Body and Arm Assembly
Jackson part # 30-983 Left Hand Body and Arm AssemblyHousing Shown in Aluminum
G1085XX -
Jackson Panic Device 1095 Active Housing
The Jackson Panic Device 1095 Active Housing is the working side of the 1095 panic hardware. The housing comes will all the internal parts, including the latch bolt. The distance between the mounting studs on this case is 6-5/16". Jackson part # 30-988 Right Hand Body, and part # 30-989 Left Hand Body
Left Hand Housing shown in the aluminum finish.
G1095xx -
Jackson Panic Device 1095 Standard Strike
The Jackson Panic Device 1095 Standard Strike is a strike they have been using for the past 20 years. You might have one of the older roller strikes, but this will work in its place. The older style roller strike is no longer available. Jackson Exit Device part # 30-2436.
G109556 -
Jackson Panic Device Top Bolt Trip 1085/1285/2086
The Jackson Panic Device Top Bolt Trip is for use on the 1085, 1285, and 2086 devices. The 30-824 Trip Assembly mounts on the jamb stop and has a pin that sticks out of it (actually a threaded set screw). The pin lines up with the release plate on the Top Bolt Guide Assembly, when the pin hits the top plate as the door closes, it releases the rods, so they can extend.
G108558 -
Jackson Panic Device 1085 and 1095 Thumb Piece Dogging Pin 30-1117
The Jackson Panic Device 1085 and 1095 Thumb Piece Dogging Pin 30-1117 is a replacement for the Screw Driver Headed Dogging Pin. Now instead of using a screw driver you can use the handy thumb piece instead. The package comes with new set screw, spring, and of course the pin. Jackson part number 30-1117.
G108554TP -
Jackson Panic Device 2085 Dogging Assembly LH/RHRB
Jackson Exit Device 2085 Dogging Assembly LH/RHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2462
This spring would be for the Device on the Right, shown below.
G302462 -
Jackson Panic Device 2085 Dogging Assembly RH/LHRB
Jackson Exit Device 2085 Dogging Assembly RH/LHRB
This Jackson Exit Device dogging assembly is used on the 2085 Device made after October 1, 1999. It will work on the previous version of this exit device, but you may have to use a file a remove some material from the catch.
Jackson Part # 30-2467
This spring would be for the Device on the Left, shown below.
G302467 -
Jackson Panic Device 1295 Push Pad End Cap Package
Jackson Panic Device 1295 Push Pad End Cap Package
Package includes two end caps, one bracket mounting screw, and 4 end mounting screws. This product was just upgraded to a metal cover, which will replace the old plastic cover.
Old Jackson part # 30-2677
New Jackson Part # 30-2654G302677-xx -
Jackson Panic Device 1285 Push Pad End Cap Package
Jackson Panic Device 1285 Push Pad End Cap Package
Package includes two end caps, one bracket mounting screw, and 4 end mounting screws. This product was just upgraded to a metal cover, which will replace the old plastic cover.
Old Jackson part # 30-2661
New Jackson Part # 30-2652-628 or 30-2652-313G302661- -
Jackson 30-2674 1285/1295 Cover Package
Jackson 30-2674 1285/1295 Cover Package
Jackson part # 30-2674-313 and 30-2674-628 Cover Plate for use on the 1285 and 1295 devices.. Plates measure 2-11/16" x 7-1/2 and 2-11/16" x 2-1/8", two plates in each package.
Jackson Part #'s 30-2674-313 and 30-2674-612
G302674- -
Jackson 1085 30-1242 / 30-1243 Lever Arms
The Jackson 1085 30-1242 / 30-1243 Lever Arms are for use with the Jackson 1085 Housings, both sides. And the Jackson 1095 Inactive (hinge side) Housings. To determine hand, stand inside and look out the door, what is side is the arm on? If it is on the Right then order Right.
G10852x -
Jackson 1095 30-1247 / 30-1248 Lever Arm
The Jackson 1095 30-1247 / 30-1248 Lever Arm. Replacement Lever Arm for the Jackson 1095 Active Housings. This arm will only work on the 1095 Active Case! The difference between this arm and the 1085 arm is the Pin in in the top of the arm. The pin fits into the triangular linkage clip, which actuates the latch bolt. Handing is determined by standing inside and looking out, if the arm in on the right hand side of the door, it is a right hand lever that you would order.
G10955X
